Skip to main content
Offline charger

Connection issues with chargepoints

Updated over a month ago

An offline charger can cause problems with charging, accepting charge cards and logging transactions.

This article is for chargers with status "Offline".

If the status of your charger is "Never Seen", it means it was never online. If nothing in this article fixes the issue, check πŸ”—Charger can't connect to Volt Time Cloud

How to fix

General

Any charger

  • Check for outages at status.volttime.com

  • Try rebooting the charger. If possible, unplug the car(s) and charging cable(s) first.
    β€‹πŸ”—How to reboot your charger

  • If there is no active LED or display, the charger may be turned off.

Specific to Volt Time chargers

  • Check the LED color. If it's white, the charger is booting. If it remains white, something is wrong and you should contact your installer.
    β€‹πŸ”—Contact installer

  • For serial numbers below 0007000

    • If your charger is connected via WiFi, you need to wait 45-60 minutes after rebooting before it will be online again.

    • After you've rebooted the charger and the LED turns green or red, stand right next to the charger and check for a network called "VoltTime_[SerialNumber]" or similar. If this network doesn't appear, you should contact your installer.

Per connectivity method

If the above steps don't fix the issue, you can try a few more things based on the way the charger is connected to the internet.

WiFi or Ethernet (RJ45)

  • Has anything changed in the network like a different provider, different modem or a change in settings?

  • Log into the network on a seperate device and use an IP scanner to see if the charger's IP is present on the network. If you cannot find the charger, that means the charger cannot connect to the building's network in the first place.

  • Log into the router and make sure:

    • Ports 80 and 443 are opened.

    • There is no firewall blocking the connection.

    • The MAC address of the charger is not blocked.

  • Sometimes "guest" networks have extra protection, just like you need to enter a username+password in a hotel. The charger has no interface for this. It must be connected to a different, less protected network.

Ethernet (RJ45)

  • Check if the data port lights on the router/switch are blinking green.

  • Check if the internet cable has been crimped correctly.

  • Check the color codes on both ends of the cable.

  • Use a network cable tester to check the crimp quality and detect any damage to the internet cable.

  • Are you using a switch? Try plugging directly into the building's router instead.

  • Check you're using the correct RJ45 port on the charger.

  • Check if the RJ45 port on the charger isn't damaged.

WiFi

  • Did the WiFi network name or password change recently?

  • The signal strength may not be good enough. Try a WiFi extender.

  • Most chargers can only connect to a 2,4GHz WiFI network.

  • You may have incorrectly entered the WiFi name and password.

SIM

  • Does the charger have a good signal strength? The connection may suffer in underground parking lots or out in the countryside.

  • Is there an outage with a mobile network provider in your region?

  • Is the SIM blocked? A SIM may be blocked if:

    • Usage was abnormally high

    • You had a third party subscription service that you've cancelled, in this case the third party will often also block the SIM.

Can't find the issue?

There are still a few things you can try to get the charger online:

  • Put the charger on a different connection method like Ethernet, WiFi or SIM.

  • Place a mobile modem near the charger and connect to that network instead.

  • Try strengthening the network with a WiFi extender.

  • Try a different CAT cable or a Powerline solution.

  • Replace the network Switch

If you are using non-Volt Time hardware and are running into issues connecting to the Volt Time Cloud, it's worth checking out πŸ”—Charger can't connect to Volt Time Cloud

If you've checked out that article and truly nothing helps, try contacting your installer.

πŸ”—Contact installer

Did this answer your question?